S.C. Office: (843)837-7900

​G.A. Office: (912)232-7687

Receive Elevator Lift Systems, Inc. quote and spec sheet

  • Typically done during home bid proposal

Elevator Ordering

  • During the framing / sheetrock phase
  • Typical 6 week lead time

Equipment Installation

  • Phase 1:  rail and sling placement 

Car Delivery

  • Typically 3 days after Phase 1 completion 

Car Detailing

  • Once car is set Contractor to trim and stain car. 
  • Note: Prefinished cars available.
  • Install hall way doors and knobs

Elevator Completion

  • Once car is detailed Elevator Lift Systems, Inc. returns to complete
  • Typically 2 days 

Elevator Inspection

  • Activate phone service to have working phone in elevator
  • Contractor to call for elevator inspection 
  • Notify Elevator Lift Systems, Inc. to have our representative on site 

3 x 5 rule

ASME code


In a RUSH?

Elevator Lift Systems, Inc.

STOCKS

standard equipment to get your job done on TIME

 

SOUTH CAROLINA

ASME A17.1 Rule 5.3.1.4.2

Clearance between hoistway door(s) or gate(s) and landing sill(s) and car door(s) or gate(s).  The clearance between the hoistway doors or gates and the hoistway edge of the landing sill shall not exceed 3 inches  (76mm).  The distance between the hoistway face of the landing door or gate and the car door or gate shall not exceed    5 inches (127mm). 


A PLUMB HOISTWAY RAIL WALL ENHANCES THE ELEVATOR RIDE AND INCREASES THE LONGEVITY OF THE UNIT. 

 

ELEVATOR LIFT SYSTEMS, INC. IS ON CALL TO ASSIST YOU ALL THE WAY THROUGH YOUR PROJECT



Hoistway Dimensions

  • ELS-HYRDO1000
    • 60" x 60" standard to provide 15sqft car
    • 44" x 44" minimum
  • ELS-HYDRO1400
    • 70" x 70" standard to provide 20sqft car
    • 60" x 60" minimum
  • ELS-TRAC750
    • 60" x 60" standard to provide 15sqft car
    • 44" x 44" minimum

Pit Depth

  • ELS-HYDRO1000 & ELS-TRAC750
    • 10" standard
    • 8" minimum
  • ELS-HYDRO1400
    • 20" standard
    • 14" minimum


GEORGIA

GEORGIA State Law:

Clearance between hoistway door(s) or gate(s) and landing sill(s) and car door(s) or gate(s).  The clearance between the hoistway doors or gates and the hoistway edge of the landing sill shall not exceed 1 1/2 inches  (38.1mm).  The distance between the hoistway face of the landing door or gate and the car door or gate shall not exceed    3 inches (76mm). 

SCHEDULE TO KEEP YOUR PROJECT ON TIME

CONTRACTOR TO PROVIDE A HOISTWAY THAT IS SQUARE AND PLUM.  STANDARD DIMENSIONS OF 60" X 60" WILL ALLOW FOR 15SQFT.

BELOW ARE TYPICAL HOISTWAY CONFIGURATIONS.  THREE OPENING OPTIONS ARE AVAILABLE.  

Hoistway Overhead Clearance

  • ELS-HYDRO1000
    • 108" standard to provide 8' car height
    • 96" minimum
  • ELS-HYDRO1400
    • 120" standard to provide 8' car height
    • 118" minimum
  • ELS-TRAC750
    • 108" standard to provide 8' car height
    • 102" minimum

Electrical

  • 280/230 volts, single phase, 60 hertz 120 volt disconnect circuit is required

Telephone

  • A telephone line is required to provide a working phone

Hoistway configurations

builder NOTES